iFlight BLITZ F7 45A 2-6S Stack
by iFlight
Original price
€0,00
-
Original price
€0,00
Original price
€0,00
€241,99
€241,99
-
€265,99
Current price
€241,99
free return
Do you live in Belgium or The Netherlands? Then you can return your package for free!
in stock, ready to be shipped
in stock, ready to be shipped
Description
Characteristics
- Improved circuit design, better components and less electrical noise!
- DJI HD VTX connector (Plug-and-Play / no soldering required)
- FC indicator LEDs for visual troubleshooting
- Met LC-filter
BLITZ F7 V1.1 Flight Controller | |
MCU | STM32 F722 |
Gyro | BMI270 |
Barometer | DPS310 |
OSD Chip | AT7456E |
Flash | 32 MB (Blackbox-flash) |
UARTS | 6 |
Motor outputs | 4x (SH1.0 connector) |
I2C-serial | SDA / SLA-pads |
Smartaudio / IRC Tramp VTX protocol supported | |
LED-controller | And |
Beeper-pad | And |
Firmware target | IFRC-IFLIGHT_BLITZ_F722 |
Montagepatroon | 30.5 x 30.5 mm / 4 mm PCB-gatdiameter |
Dimensions | 36.5 x 35 mm |
Weight | 7.8 g |
Wiring suggestion
- UART 1 for VTX HD / Analog
- UART 2 for a receiver
- UART 3/4/5 for GPS or other sensors that require a serial port
- UART 6 for ESC telemetry
Tips
- 1. F722 MCU has an internal inverter.
- 2. SBUS、CRSF、ELRS、IBUS、DSM ETC... can be connected to any unused UART_RX, we suggest you connect to Uart_RX2
- 3. Frsky SmartPort, Tramp & Smartaudio can be connected to any unused UART_TX, we suggest you connect to Uart_TX1
- 4. F.port can be connected to any unused UART_TX, we suggest you connect to Uart_TX2
BLITZ E45S 4-IN-1 2-6S ESC | |
Support | DShot150/300/600/MultiShot/OneShot etc. |
assembly gate | 30.5 x 30.5 mm / Φ4 mm |
Supports | 2-6S liposuction |
Telemetry output | Nee |
Goal | QH-40 16.7 |
Current sensor | And |
Constant current | 45 amps |
Flow assessment | 200 |
Burst | 55 amps |
Weight | 14.7 g |
MCU | BB21 |
BEC | Nee |
Characteristics
- Stable output power
- 4 power levels up to 1600mW
- 40 channels (including Raceband)
- Fast frequency locking, no startup interference with other pilots
- Built-in output power self-check function
- VTX telemetry with IRC Tramp protocol
- VTX is set to 25mW by default! Power levels above 25mW require a HAM license or local authority approval! Make sure you are flying legal frequencies and use our prepared Betaflight VTX tables for your area.
BLITZ 1.6W VTX adjustable | |
Input voltage | 7V~36V |
Interface | MMCX |
Power levels | PIT/25mW/400mW/800mW/1600mW |
Channels | 40 (including Race Tire) |
Montagepatroon | 30.5 x 30.5 mm / Φ3 |
lightweight | 18.9 g (excluding antenna) |
VTX telemetry | IRC Tramp |
Betaflight IRC Tramp Configuration | Download the attached VTX table for Betaflight! |
All VTX tables can also be found here | LINK |
IRC Tramp VTX-tabelwaarden | 25mW/400mW/800mW/1600mW |
What's included:
- 1 PC X BLITZ F7 V1.1 FLIGHT CONTROLLER
- 1PC BLITZ E45S 4-IN-1 2-6S ESC
- 1PC X BLITZ 1.6W VTX Adjustable
- 1 SET X SILICON TRANSMITTERS
- 1SET X WIRING HARNESS FOR F7 FLIGHT CONTROLLER